By Lukeron Lubricants · Last updated
Quick answer
A technical data sheet (TDS) shows what a lubricant is for and its typical test results. The most important line is viscosity at 40 °C and 100 °C, which decides the grade. Viscosity index shows how little the oil thins when hot, flash point shows safe handling, and pour point shows how cold the oil still flows. Check that each number names its test method, and ask for the safety data sheet (SDS) too.
Data sheet lines at a glance
| Line on the TDS | What it tells you | Usual test method |
|---|---|---|
| Viscosity at 40 °C and 100 °C (cSt) | How thick the oil is. It decides the grade | ASTM D445 |
| Viscosity index | How little the oil thins as it gets hot | ASTM D2270 |
| Flash point (COC) | Safe handling and storage temperature | ASTM D92 |
| Pour point | The lowest temperature at which the oil still flows | ASTM D97 |
| Density at 15 °C | Weight per millilitre, for converting litres and kilograms | ASTM D4052 |
| Total base number (engine oils) | Reserve to neutralise acids from combustion | ASTM D2896 |
The test methods shown are the usual ones. A data sheet may name a different standard method. Typical values are results from regular production, and small batch-to-batch variation is normal.
A technical data sheet, or TDS, is a one-page summary of a lubricant: what it is, what it is used for and what its typical test results are. Buyers, workshops, plant engineers and private label brands all ask for it before they order. But the table of numbers is easy to misread. This guide explains each line of a lubricant data sheet in plain words, what to compare and what to ask the supplier.
What is a technical data sheet (TDS)?
A TDS describes the performance of a product. It usually shows the product name and grade, the recommended use, the typical properties with the test method for each, the pack sizes, and notes on storage and shelf life. It is different from the safety data sheet (SDS), which is about safe handling, first aid, fire and disposal.
TDS and SDS: the difference
- TDS (technical data sheet): how the product performs and what it is for. Read it to choose the product.
- SDS (safety data sheet): how to handle, store, transport and dispose of the product safely. Read it before you use the product.
A serious supplier gives both.
What the lines of a lubricant TDS mean
- Colour: how the oil looks. It is a quick check, not a measure of quality.
- Density at 15 °C: the weight of the oil per millilitre. It is useful for converting between litres and kilograms.
- Kinematic viscosity at 40 °C and 100 °C (cSt): how thick the oil is at those temperatures. This is the most important line. It decides the grade, such as VG 46 or SAE 40.
- Viscosity index (VI): how little the oil thins as it gets hot. A higher number means the thickness changes less with temperature.
- Flash point: the lowest temperature at which the oil gives off enough vapour to flash when a flame is brought near. It matters for safe handling and storage.
- Pour point: the lowest temperature at which the oil still flows. It matters for cold starts and cold climates.
- Total base number (TBN, for engine oils): how much reserve the oil has to neutralise acids from combustion.
- Sulphated ash (for engine oils): the ash left after burning the oil. Some engines need a low value.
- Grease lines: NLGI grade, thickener, dropping point and worked penetration, which describe how stiff the grease is and where it starts to melt.
What is a test method, and why does it matter?
Each line on a good data sheet names the test method, for example ASTM D445 for viscosity, ASTM D92 for flash point or ASTM D97 for pour point. The method matters because the same oil can give different numbers by different methods. When you compare two data sheets, compare the same method on both.
What does "typical" mean?
Most data sheets say typical values. These are results from regular production, and small batch-to-batch variation is normal. A typical value is not a promise for every drum. If you need guaranteed limits, ask the supplier for a specification with minimum and maximum values.
How to compare two data sheets
- Start with the grade the machine maker names, such as SAE 20W-40 or ISO VG 46.
- Check that the viscosity at 40 °C and 100 °C fits that grade.
- Compare the viscosity index, the flash point and the pour point.
- Check that the performance category the maker names, such as an API class, is stated by the supplier.
- Do not choose on one number. A single line does not show how the oil will behave in your machine.
Red flags on a data sheet
- No test methods next to the numbers.
- A performance claim with no category or approval named.
- Numbers that do not fit the grade, for example a viscosity that is outside the grade range.
- A sheet with no company name, date or version.
What else to ask the supplier
- A safety data sheet (SDS) for the same product.
- The pack sizes and the shelf life.
- Whether the supplier can make a test batch or send a free sample.
- For private label buyers: who owns the formula and what the minimum order is.
Lukeron product information
Lukeron makes engine oils, gear oils, greases, brake fluids, coolants and industrial oils at its own plant in Jamnagar, Gujarat. Tell us your machine, your grade and your working conditions, and we will help you choose, and send a free sample to test. Ask our team for the details you need for your application.
