By Lukeron Lubricants · Last updated
Quick answer
Most 100 to 160 cc Indian bikes do not need a separate gear oil. The gearbox shares the engine oil, so use the 4T engine oil your manual names. A separate gear oil is for scooter gear cases, rear axles, 3-wheelers and any gearbox with its own oil filler. The two levels you will see are GL-4 (for gearboxes with brass or bronze parts) and GL-5 (more extreme pressure additive, for hypoid gears under heavy load). Use the grade and API level the maker names. Do not swap GL-5 into a GL-4 gearbox unless the maker allows it.
Which oil goes where
| Where | What it usually needs | Lukeron option |
|---|---|---|
| Commuter bike with a shared gearbox | The 4T engine oil the manual names, wet-clutch compatible. No separate gear oil | SPL 4-Stroke 20W-40 API SN; SPL 4-Stroke 10W-30 API SN |
| Scooter gear case | A small amount of the gear oil grade the manual names | Ask our team with your scooter model |
| Separate gearbox that names GL-4 | GL-4 gear oil. GL-5 can harm brass and bronze parts | We make both GL-4 and GL-5 gear oils. Send us the grade from your manual |
| Rear axle or hypoid gears, heavy load | GL-5 gear oil, when the maker names it | SPL Gear Oil EP 80W-90 GL-5 |
General guidance only. Follow the vehicle maker's manual for oil grade, API level and quantity.
Most motorcycle riders are vigilant about engine oil but surprisingly casual about gearbox oil. Yet the gearbox and final drive on a motorcycle take enormous abuse — particularly on Indian roads with their frequent gear changes, stop-start traffic, and occasional overloading. The wrong gear oil, or degraded gear oil, leads to difficult gear shifting, premature synchromesh wear, and in worst cases, gear tooth failure.
Do All Motorcycles Need Separate Gear Oil?
Many Indian 2-wheelers use a common wet clutch gearbox that shares oil with the engine crankcase. For these bikes, a 4T motorcycle engine oil with wet clutch compatibility is used for both engine and gearbox. Separate gear oil is not required. Some motorcycles, scooters, most 3-wheelers and small 4-wheelers have a separate gearbox or final drive that needs its own gear oil. The owner's manual says which.
API GL-4: The Motorcycle Transmission Standard
Many separate motorcycle gearboxes and manual car transmissions name API GL-4. GL-4 provides moderate extreme pressure protection suitable for synchronised gear sets. Its milder EP additive package is the reason it is named for gearboxes with brass synchromesh rings or bronze parts. Always use the class the owner’s manual names.
API GL-5: For Hypoid Gears and Heavy Loads
GL-5 contains significantly higher concentrations of EP additives — particularly sulphur compounds — to handle the extreme sliding contact in hypoid gear sets (where pinion and ring gear axes do not intersect). It is specified for rear axle differentials, transfer cases, and some heavy-duty transmissions. Some manual gearboxes with brass or bronze parts are made for GL-4 and do not accept GL-5, so do not use GL-5 in a gearbox that names GL-4.
Gear Oil for 3-Wheelers and Light Vehicles
Three-wheelers, small 4-wheelers and cars each have their own gearbox oil requirement. Some name 80W-90, others a thinner grade such as 75W-90, and some name GL-4 while others name GL-5. The owner’s manual decides: use the viscosity grade and the API class it names.
How Often Should Motorcycle Gear Oil Be Changed?
For separate gearboxes, follow the change interval in the owner’s manual. The oil should be changed while warm (after a short ride) to ensure better drain-out of contaminants and metal particles. If gear shifting becomes notchy or difficult before the interval is due, check the oil level and condition first — this is often the first symptom of degraded gear oil.
Lukeron SPL Gear Oil EP 80W-90 GL-5 is available for automotive and industrial use. Contact: +91 73832 79438 | www.lukeronlubricants.com
