By Lukeron Lubricants · Last updated
Quick answer
DOT 3 and DOT 4 are two glycol-based brake fluids. DOT 4 is made to a higher level, with a higher minimum boiling point, so it resists boiling better under hard braking. Both absorb water from the air over time, so both must be replaced on schedule. Use the class your vehicle manual or reservoir cap names, never mix them with silicone-based DOT 5, and change the fluid as the manual says.
Brake fluid types at a glance
| Type | Base | What to know |
|---|---|---|
| DOT 3 | Glycol | Common in many ordinary cars and light vehicles |
| DOT 4 | Glycol | Higher minimum boiling point, often named for newer cars and heavier work |
| DOT 5.1 | Glycol | Glycol-based like DOT 3 and 4, made to a higher level still |
| DOT 5 | Silicone | Not compatible with DOT 3 and DOT 4, do not mix |
General guidance only. Follow the vehicle maker's manual or the reservoir cap for the class of brake fluid.
Brake fluid is the liquid that carries your foot's push from the brake pedal to the brakes at each wheel. When you see DOT 3 and DOT 4 on a bottle, they are two common types of this fluid. Many drivers wonder which one to buy, whether they can mix them and how often to change them. This guide answers these questions in plain words.
What is brake fluid?
Brake fluid is a hydraulic fluid. When you press the pedal, the fluid pushes in the brake lines and moves the pistons that squeeze the pads or shoes against the disc or drum. A liquid cannot be squeezed, so the push arrives at every wheel at once. The fluid must also stay liquid in the cold, resist boiling in the heat of hard braking, and protect the metal and rubber parts inside the brake system.
What does DOT 3 and DOT 4 mean?
DOT stands for the US Department of Transportation. The number is the class of the fluid under a standard that sets minimum performance, mainly how hot the fluid can get before it boils and how thick it is in the cold. DOT 3 and DOT 4 are both glycol-based fluids. DOT 4 is made to a higher performance level than DOT 3, so it is meant to resist boiling better.
DOT 3 vs DOT 4: the main difference
- Boiling point: DOT 4 has a higher minimum boiling point than DOT 3, both when new (dry) and after it has taken in some water (wet).
- Moisture: both are glycol-based and both absorb water from the air over time. Brake fluid that has absorbed water boils at a lower temperature, so it must be replaced on schedule.
- Use: DOT 3 suits many ordinary cars and light vehicles. DOT 4 is often named for newer cars, vehicles that brake hard, and vehicles with ABS and a heavier load.
- Price: DOT 4 usually costs a little more than DOT 3.
Which brake fluid should I use?
Use the type your vehicle's manual or the cap of the brake fluid reservoir names. The maker has designed the brake system for that class. If the manual names DOT 3, you can often use DOT 4, because DOT 4 meets a higher level and both are glycol-based, but check the manual. If the manual names DOT 4, do not drop to DOT 3. Do not guess from a friend's car, because the right fluid depends on your vehicle.
Can I mix DOT 3 and DOT 4?
Both are glycol-based, so they can normally be mixed without damaging the system. But a mix is only as good as the weaker fluid, so it is better to flush the system and fill it with one fluid. Never mix them with DOT 5, which is silicone-based and is not compatible with DOT 3 and DOT 4. Also note that DOT 5.1 is a glycol-based fluid, despite its number. Always check the cap and the manual first.
Why brake fluid must be changed
Brake fluid is hygroscopic, which means it takes in moisture from the air through hoses and seals, even in a closed system. Over time the water lowers the boiling point of the fluid. Under hard braking, such as a long downhill road or a heavy load, the fluid can then boil and make bubbles. Bubbles can be squeezed, so the pedal feels soft and braking can fade. Water can also cause rust and damage inside the brake parts.
How often should brake fluid be changed?
Follow the interval in the vehicle manual or service schedule. Many makers ask for a change after a number of years rather than after a number of kilometres, because the fluid ages even when the vehicle is parked. Trucks, vehicles on hilly roads and vehicles that carry heavy loads often need checks sooner. Have the fluid tested or changed at a workshop if the pedal feels soft or spongy.
Handling and safety tips
- Keep the bottle sealed. An open bottle takes in moisture and should not be kept for a long time.
- Do not spill brake fluid on paint. It can damage the paint, so wipe it off at once.
- Use clean fluid from a new, sealed container for topping up and bleeding.
- Do not use mineral oil, engine oil or any other liquid in the brake system. They can damage the rubber seals.
- Dispose of old brake fluid properly. Do not pour it on the ground or down a drain.
Brake fluid for trucks, fleets and workshops
Workshops and fleets that service many vehicles can buy brake fluid in small bottles for retail jobs or in larger packs for regular service. Use the class that each vehicle's manual names, keep the containers sealed, and note the date of each brake fluid change in the service record.
Lukeron brake fluid
Lukeron Lubricants makes SPL Brake Fluid in DOT 3 and DOT 4. They are packed in small bottles for the retail counter and in drums for workshops and fleets. We offer free samples to garages, OEMs and industries, and we also handle private label orders. Send your enquiry with the class and the pack size you need, and we reply within 24 hours.
